|
The JMAG Users Conference is a conference held once each year in various
locations around the world aiming to share technological information with
JMAG users. The JMAG Users Conference is a place for an active technological
exchange of information from presentations introducing the newest technology
worldwide to examples presented by JMAG users and poster sessions created
by the JMAG engineers.
[Overview]
The JMAG Users Conference 2009 came to a close successfully with more than
280 participants. We would like to thank all of the users and presenters,
as well as the exhibitors for their participation in the JMAG Users Conference.
The JMAG Users Conference 2009 was focused around examples presented by
JMAG users, seminars introducing the newest solutions, poster sessions
held by the JMAG engineers, and exhibitions by various exhibitors. Various
presenters introduced user examples and the newest solutions in the general
session, special session, transformer session, and induction heating session
that composed the conference program.
Many whom attended the conference expressed their interest in the special
session held on the first day of the conference, "Discovery and Expansion
of IPM Motors - Innovation of Mature Devices -." We are proud that
the theme of the JMAG Users Conference 2009, "Discovery," was
meaningful to all those whom attended. We thank everyone for their support
and participation and we look forward to your continued support in the
future.
[General Session]
- JMAG Users Conference Thursday, December 10
- Development Planning of JMAG
Dr. Takashi Yamada, JSOL Corp.
- Interior PM Synchronous Machines: Historical Perspectives, Current Status,
and Future Directions
Prof. Thomas M. Jahns, University of Wisconsin
- Product Development and Market Expansion for IPM Motors
Mr. Toshiaki Idemitsu, Manager, Engineering Department, Yaskawa Motor Corporation
- Development and Challenges of Motors for Toyotafs Hybrid Vehicles
Prof. Akihide Takahara, Group Manager, Hybrid Vehicle
Advanced Technology Engineering Div., Toyota Motor Corporation
- Loss Analysis and Shape Optimization of Interior Permanent Magnet Motors
Prof. Katsumi Yamazaki, Professor, Dept. of Electrical, Electronics, and
Computer
Engineering, Chiba Institute of Technology
- AcuSolve: 3D Thermal Flow Analysis of JMAG Results
Farzin Shakib, President, ACUSIM Software, Inc.
- Virtual Motor Capable of Connecting to an Inverter that Supports Nonlinear
Response
(JMAG-RT Compatible)
Mr. Yoshihiko Ozaki, Development Division, DSP Technology, Co., Ltd.
- A Study of Generating Factor of the Electromagnetic Excitation Forces and
Development of Low-noise Motors
Dr. Yoshio Yoshikuwa, Head Researcher, Advanced Technology R&D Center,
Mechatronics Department, Mitsubishi Electric Corporation
- JMAG Users Conference Friday, December 11
- The Newest Developments of Rare-earth Magnets
Dr. Dai Higuchi, Executive Researcher, Magnet Material Research Center
2nd Development Dep., ShinEtsu Chemical Co., Ltd.
- Examination of a Torque Estimation Method by Using JMAG-RT
Mr. Hajime Hida, Chief Researcher, ECO Technology Research Center Power
Systems Research Department, SANYO Electric Co., Ltd.
- Expectations from Control Technology to Magnet Field Analysis
Dr. Shinji Doki, Associate Professor, Department of Electrical Engineering
ad Computer Science, Graduate School of Engineering, Nagoya University
- Development of Motor for Small Car HEV and Introduction of Co-simulation
of Motor Inverter using JMAG-RT
Mr. Masahiro Aoyama, Automobile Powertrain Design Dept. I, Suzuki Motor
Corporation
- Utilizing a Magnetic Field Analysis for a Hybrid Stepping Motor
Mr. Masaru Kobori, General Manager, Oriental Motor Co., Ltd.
- Simulation of Small Wind Power Generation System Using PMSG
Dr. Katsumi Kesamaru, Associate Professor, Graduate School of Information
Science and Electrical Engineering, Kyushu University
- Analysis of Nonlinear Characteristics in High Temperature Superconductor
Rotating Machine
Dr. Taketsune Nakamura, Associate Professor, Department of Electrical Engineering,
Graduate School of Engineering, Kyoto University
- Engineerfs Education Using Electromagnetics CAE at Mitsubishi Electric
Mr. Hidenobu Itagaki, Chief Engineer, Human Resources Development Center,
Mitsubishi Electric Corporation
- Report of Harumi-1 Project
Mr. Katsuyuki Narita, Mr. Tetsuya Hattori, JSOL Corporation
[Transformer Session]
- Development and Performance Evaluation of a Contactless Induction Power
Supply (IPS) System for Electric-driven Vehicles
Dr. Yushi Kamiya, Professor, Faculty of Science and Engineering, Waseda
University
- Consideration of the Joule Loss in Windings for Power Reactor
Mr. Tsutomu Hamada, Design Group, Automotive Components Department, Electronic
Components Business Sector, Tamura Corporation
- Parametrizing the Coil Construction and Coupling Coefficients of Inverter
Transformers in JMAG
Mr. Masahiro Kitagawa, Electronic Circuit Development Department Development
Division Electronic Device & Component Transformer Session Seminar
- Designing Transformers and Estimating Problems and Countermeasures
[Induction Heating Session]
- Examples Utilizing JMAG
Mr. Shunsuke Funaji, Power Electronics Design Dept. Machinery Factory Machinery
& System Hq., Mitsui Engineering & Shipbuilding Co., Ltd.
- Crankshaft Optimization of Induction Heat Treatment Using Computer Aided
Engineering
Ms. Akiko Inami, Advanced Manufacturing Technology Dept., Fuji Heavy Industries
Ltd.
- Examination of an Induction Heating Simulation Using B-H Curve
Mr. Takashi Horino, Chief, CAE Development Section, Development Department,
Technical Headquarters, Neturen Co., Ltd.
|
