Component Properties for the Thermal Circuit

Fixed Temperature(FixedTemperature)

The fixed temperature

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
FixedTemperature	Double		The fixed temperature

Foot Mounting Base(FootMountingBase)

The foot mounting base

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
RemoveFromMotor	Flag	0 or Not remove 1 or Remove	The flag to remove base from motor The base is used. The base is removed from motor.
FootMaterialType	Flag	0 or Custom 1 or S45C 2 or SUS304 3 or Aluminium	The type of foot material Use custom. Use S45C. Use SUS304. Use Aluminium.
FootDensity	Double		The foot density
FootThermalConductivity	Double		The foot thermal conductivity
FootSpecificHeat	Double		The foot specific heat
FootWidthMotor	Double		The foot width (motor)
FootWidthBase	Double		The foot width (base)
FootLength	Double		The foot length
FootThicknessMotor	Double		The foot thickness (motor)
FootThicknessBase	Double		The foot thickness (base)
BaseMaterialType	Flag	0 or Custom 1 or S45C 2 or SUS304 3 or Aluminium	The type of base material Use custom. Use S45C. Use SUS304. Use Aluminium.
BaseDensity	Double		The base density
BaseThermalConductivity	Double		The base thermal conductivity
BaseSpecificHeat	Double		The base specific heat
BaseWidth	Double		The base width
BaseThickness	Double		The base thickness
BaseLength	Double		The base length
BaseTemperature	Double		The base temperature
HousingFootFitType	Flag	0 or Custom 1 or GoodFit 2 or BadFit	The flag for housing foot fit type Use custom. Use good fit. Use bad fit.
HousingFootGap	Double		The housing foot gap
HousingFootThermalConductivity	Double		The housing foot thermal conductivity
FootBaseFitType	Flag	0 or Custom 1 or GoodFit 2 or BadFit	The flag for foot base fit type Use custom. Use good fit. Use bad fit.
FootBaseGap	Double		The foot base gap
FootBaseThermalConductivity	Double		The foot base thermal conductivity
AmbientTemperature	Double		The ambient temperature
UseAutoCalculation	Flag	0 or Off 1 or On	Use auto calculation Not using auto calculation Using auto calculation
HousingFootResistanceCorrectionCoefficient	Double		The correction coefficient of housing foot resistance
FootResistanceCorrectionCoefficient	Double		The correction coefficient of foot resistance
FootCapacitanceCorrectionCoefficient	Double		The correction coefficient of foot capacitance
FootBaseResistanceCorrectionCoefficient	Double		The correction coefficient of foot base resistance
BaseResistanceCorrectionCoefficient	Double		The correction coefficient of base resistance
BaseCapacitanceCorrectionCoefficient	Double		The correction coefficient of base capacitance
NaturalConvectionCorrectionCoefficient	Double		The correction coefficient of natural convection

Flange Mounting Plate(FlangeMountingPlate)

The flange mounting plate

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
RemoveFromMotor	Flag	0 or Not remove 1 or Remove	The flag to remove plate from motor The plate is used. The plate is removed from motor.
StatorDiameter	Double		The stator diameter
HousingThickness	Double		The housing thickness
FlangeDiameter	Double		The flange diameter
FlangeExtension	Double		The flange extension
FlangeDepth	Double		The flange depth
PlateMaterialType	Flag	0 or Custom 1 or S45C 2 or SUS304 3 or Aluminium	The type of plate material Use custom. Use S45C. Use SUS304. Use Aluminium.
PlateDensity	Double		The plate density
PlateThermalConductivity	Double		The plate thermal conductivity
PlateSpecificHeat	Double		The plate specific heat
PlateHeight	Double		The plate height
PlateWidth	Double		The plate width
PlateThickness	Double		The plate thickness
PlateTemperature	Double		The plate temperature
FlangePlateFitType	Flag	0 or Custom 1 or GoodFit 2 or BadFit	The flag for flange plate fit type Use custom. Use good fit. Use bad fit.
FlangePlateGap	Double		The flange plate gap
FlangePlateThermalConductivity	Double		The flange plate thermal conductivity
AmbientTemperature	Double		The ambient temperature
UseAutoCalculation	Flag	0 or Off 1 or On	Use auto calculation Not using auto calculation Using auto calculation
FitResistanceCorrectionCoefficient	Double		The correction coefficient of fit resistance
PlateResistanceCorrectionCoefficient	Double		The correction coefficient of plate resistance
PlateCpacitanceCorrectionCoefficient	Double		The correction coefficient of plate capacitance
NaturalConvectionCorrectionCoefficient	Double		The correction coefficient of natural convection

Coil End Cooling(CoilEndCooling)

The coil end cooling

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
ThermalResistance	Double		The thermal resistance (coil end)
HeatCapacity	Double		The heat capacity (coil end)
CoolingType	Flag	0 or Thermal Resistance (Constant) 1 or Natural Convection 2 or Forced Convection 3 or Mixed Convection 4 or Spray 5 or ATF Spray (Top) + ATF Pool 6 or ATF Spray (Sides) + ATF Pool 7 or Thermal Resistance (Constant1~4) 8 or Thermal Resistance (User-Defined)	The cooling type Using a constant thermal resistance Using natural convection cooling Using forced convection cooling Using mixed convection cooling Using spray cooling Using ATF spray (Top) and ATF pool cooling Using ATF spray (Sides) and ATF pool cooling Using 4 constant thermal resistances User-Defined thermal resistances
TwoTerminalCoilEndCooling	Flag	0 or Off 1 or On	Two terminal coil end cooling component for ATF Spray and ATF pool Three terminal coil end cooling component for ATF Spray and ATF pool Two terminal coil end cooling component for ATF Spray and ATF pool
StartAngle	Double		The start angle
RangeAngle1	Double		The range angle 1
RangeAngle2	Double		The range angle 2
RangeAngle3	Double		The range angle 3
ThermalResistanceCooling1	Double		Constant / Constant 1 (Cooling)
ThermalResistanceCooling2	Double		Constant 2 (Cooling)
ThermalResistanceCooling3	Double		Constant 3 (Cooling)
ThermalResistanceCooling4	Double		Constant 4 (Cooling)
ConvectionCoolantType	Flag	0 or Air 1 or Water 2 or Oil 3 or ATF Oil 4 or Custom	The flag for convection coolant type Use air. Use water. Use oil. Use ATF oil. Use custom.
ATFCoolantType	Flag	3 or ATFOil 4 or Custom	The flag for ATF coolant type Use ATF oil. Use custom.
ConvectionThermalArea	Double		The convection thermal area
CorrectionCoefficient	Double		The correction coefficient
CoolantTemperature	Double		The coolant temperature
ForcedConvectionType	Flag	0 or Circumferential 1 or AxisDirection 2 or MotorGap	The flag for forced convection type Use circumferential. Use axis direction. Use motor gap (radial).
ConvectionInputFlowType	Flag	0 or FlowVelocity 2 or ReferenceFlowCircuit	The flag for convection input flow type Use flow velocity. Reference flow circuit.
ConvectionFlowVelocity	Double		The convection flow velocity
ConvectionReferenceFlowRateProbe	Int		The convection referenced flow rate probe id
PreviewConvectionFlowVelocity	Double		The convection flow velocity (preview)
GapWidth	Double		The gap width
RotorRadius	Double		The rotor radius
CharacteristicLengthForced	Double		The characteristic length (forced)
NaturalConvectionType	Flag	0 or HorizontalCylinder 1 or VerticalCylinder 2 or VerticalFlatPlate 3 or HorizontalPlateUpper 4 or HorizontalPlateLower	The flag for natural convection type Use horizontal cylinder. Use vertical cylinder. Use vertical flat plate. Use horizontal plate upper. Use horizontal plate lower.
CharacteristicLengthNatural	Double		The characteristic length (natural)
CorrectionNatural	Double		The correction coefficient (natural)
MixedDirectionType	Flag	0 or AssistingOrTransverse 1 or Opposing	The flag for mixed direction type Assisting or Transverse. Opposing.
TerminalTemperature	Double		The terminal temperature (preview)
ConvectionPreviewCoolantTemperature	Double		The coolant temperature (preview)
SprayType	Flag	0 or GeneralSpray 1 or SpecifyNozzlePosition	The flag for spray type General spray. Specify nozzle position.
NozzlePosition	Flag	0 or SprayHousing 1 or SprayEndCap 2 or SprayShaft 3 or SprayHousingAndEndCap 4 or SprayHousingAndShaft 5 or SprayEndCapAndShaft 6 or SprayHousingAndEndCapAndShaft	The flag for nozzle position Spray from housing. Spray from end cap. Spray from shaft. Spray from housing and end cap. Spray from housing and shaft. Spray from end cap and shaft. Spray from housing and end cap and shaft.
CoolantType	Flag	1 or Water 2 or Oil 4 or Custom	The flag for coolant type Use water. Use oil. Use custom.
SprayATFInputFlowType	Flag	0 or FlowVelocity 1 or VolumeFlowRate	The flag for spray or ATF flow type Use flow velocity. Use volume flow rate.
SprayATFFlowVelocity	Double		The spray or ATF flow velocity
SprayATFVolumeFlowRate	Double		The spray or ATF volume flow rate
NozzleDiameter	Double		The nozzle diameter
SprayATFThermalResistorArea	Double		The spray or ATF thermal resistor area
SprayATFThermalCorrection	Double		The spray or ATF thermal correction coefficient
SprayPreviewCoolantTemperature	Double		The coolant temperature (preview)
CoilEndHeight	Double		The coil end height
CoilOuterRadius	Double		The coil outer radius
CoilInnerRadius	Double		The coil inner radius
CoilEndAreaCorrectionType	Flag	0 or UseCorrectionCoefficient 1 or UseCoilEndSurfaceArea	The flag for spray coil end area correction type Use correction coefficient. Use coil end surface area.
CoilEndAreaCorrectionCoefficient	Double		The spray coil end area correction coefficient
CoilEndSurfaceArea	Double		The coil end surface area
SprayHousingInputFlowType	Flag	0 or FlowVelocity 1 or VolumeFlowRate	The flag for spray or ATF flow type Use flow velocity. Use volume flow rate.
SprayHousingFlowVelocity	Double		The spray or ATF flow velocity
SprayHousingVolumeFlowRate	Double		The spray or ATF volume flow rate
SprayHousingNozzleDiameter	Double		The nozzle diameter
SprayHousingNozzleNumber	Flag		The number of nozzles
SprayHousingFirstNozzleAngle	Double		The first nozzle angle
SprayHousingSprayAngle	Double		The spray angle
SprayHousingHousingInnerRadius	Double		The housing inner radius
SprayHousingThermalCorrection	Double		The spray or ATF thermal correction coefficient
SprayEndCapInputFlowType	Flag	0 or FlowVelocity 1 or VolumeFlowRate	The flag for spray or ATF flow type Use flow velocity. Use volume flow rate.
SprayEndCapFlowVelocity	Double		The spray or ATF flow velocity
SprayEndCapVolumeFlowRate	Double		The spray or ATF volume flow rate
SprayEndCapNozzleDiameter	Double		The nozzle diameter
SprayEndCapNozzleNumber	Flag		The number of nozzles
SprayEndCapFirstNozzleAngle	Double		The first nozzle angle
SprayEndCapSprayAngle	Double		The spray angle
SprayEndCapEndCapDistance	Double		The end cap distance
SprayEndCapThermalCorrection	Double		The spray or ATF thermal correction coefficient
SprayShaftInputFlowType	Flag	0 or FlowVelocity 1 or VolumeFlowRate	The flag for spray or ATF flow type Use flow velocity. Use volume flow rate.
SprayShaftFlowVelocity	Double		The spray or ATF flow velocity
SprayShaftVolumeFlowRate	Double		The spray or ATF volume flow rate
SprayShaftNozzleDiameter	Double		The nozzle diameter
SprayShaftNozzleNumber	Flag		The number of nozzles
SprayShaftSprayAngle	Double		The spray angle
SprayShaftShaftOuterRadius	Double		The shaft outer radius
SprayShaftThermalCorrection	Double		The spray or ATF thermal correction coefficient
CoolingMaterialTable	Table		The cooling material table
CoolantTemperatureType	Flag	0 or Constant 1 or TerminalAverageValue	The flag for coolant temperature type Use constant. Refer to Terminal Average Value.
CoolantSourceTemperature	Double		The cooling source temperature
MonitorCoilEndTemp	Flag	0 or Off 1 or On	Monitor coil end temperature Do not monitor coil end temperature Monitor coil end temperature
UseVariableCoolantTemperature	Flag	0 or Off 1 or On	Use variable coolant temperature Do not use vaiable coolant temperature Use variable coolant temperature
ThermalUserDefinedScript	String		The python script for thermal resistance
RotationSpeedType	Flag	0 or Constant 1 or PointArray 2 or DriveCycleReference	The flag for rotation speed type The constant type. The point array type. Reference Condition
RotationSpeed	Double		Rotation Speed
RotationSpeedVsTime	Table		The rotation speed vs time point array
ReferDriveCycleCondition	Int		Refer drive cycle condition

Convection Cooling(ConvectionCooling)

The convection cooling

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
ConvectionType	Flag	0 or Forced 1 or Natural 2 or Mixed	The flag for convection type The forced convection type. The natural convection type. The mixed convection type.
CoolantType	Flag	0 or Air 1 or Water 2 or Oil 3 or ATF 4 or Custom	The flag for coolant type Use air. Use water. Use oil. Use ATF oil. Use custom.
Thermal Area	Double		The thermal area
CoolantTemperature	Double		The coolant temperature
CorrectionCoefficient	Double		The correction coefficient
ForcedConvectionType	Flag	0 or Circumferential 1 or AxisDirection 2 or MotorGap	The flag for forced convection type Use circumferential. Use axis direction. Use motor gap (radial).
InputFlowType	Flag	0 or FlowVelocity 2 or ReferenceFlowCircuit	The flag for input flow type Use flow velocity. Reference flow circuit.
FlowVelocity	Double		The flow velocity
ReferenceFlowRateProbe	Int		The referenced flow rate probe id
PreviewFlowVelocity	Double		The flow velocity (preview)
GapWidth	Double		The gap width
RotorRadius	Double		The rotor radius
CharacteristicLengthForced	Double		The characteristic length (forced)
NaturalConvectionType	Flag	0 or HorizontalCylinder 1 or VerticalCylinder 2 or VerticalFlatPlate 3 or HorizontalPlateUpper 4 or HorizontalPlateLower	The flag for natural convection type Use horizontal cylinder. Use vertical cylinder. Use vertical flat plate. Use horizontal plate upper. Use horizontal plate lower.
CharacteristicLengthNatural	Double		The characteristic length (natural)
MixedDirectionType	Flag	0 or AssistingOrTransverse 1 or Opposing	The flag for mixed direction type Assisting or Transverse. Opposing.
TerminalTemperature	Double		The terminal temperature (preview)
CoolingMaterialTable	Table		The cooling material table
CoolantTemperatureType	Flag	0 or Constant 1 or TerminalAverageValue	The flag for coolant temperature type Use constant. Refer to Terminal Average Value.
CoolantSourceTemperature	Double		The cooling source temperature
PreviewCoolantTemperature	Double		The coolant temperature (preview)
HasFins	Flag	0 or Off 1 or On	The flag for fins The surface does not have fins. The surface has fins.
FinInterval	Double		The fin interval
FinLength	Double		The fin length
FinHeight	Double		The fin height
FinNumber	Flag		The fin number

Shaft Cooling(ShaftCooling)

The shaft cooling

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
InputFlowType	Flag	0 or FlowVelocity 1 or VolumeFlowRate 2 or ReferenceFlowCircuit	The flag for input flow type Use flow velocity. Use volume flow rate. Reference flow circuit.
FlowVelocity	Double		The flow velocity
VolumeFlowRate	Double		The volume flow rate
ReferenceFlowRateProbe	Int		The referenced flow rate probe id
PreviewVolumeFlowRate	Double		The volume flow rate (preview)
PreviewFlowVelocity	Double		The flow velocity (preview)
ShaftCoolingType	Flag	0 or NoShaftCooling 1 or HollowShaftCooling	The flag for shaft cooling type No Shaft Cooling Hollow Shaft Cooling
ShaftLength	Double		The shaft length
ShaftRotorHeight	Double		The shaft rotor height
ShaftOuterRadius	Double		The shaft outer radius
ShaftInnerRadius	Double		The shaft inner radius
ShaftMassDensity	Double		The shaft mass density
ThermalConductivity	Double		The shaft thermal conductivity
ShaftCoolingSpecificHeat	Double		The shaft specific heat
ShaftCorrection	Double		The shaft correction coefficient
AdvectiveHeatTransportCorrection	Double		The advective heat transport correction coefficient
ShaftCoolantType	Flag	1 or Water 2 or Oil 3 or ATFOil 4 or Custom	The flag for shaft coolant type Use water. Use oil. Use ATF oil. Use custom.
CoolingMaterialTable	Table		The cooling material table
CoolantTemperatureConstantValue	Double		The coolant temperature constant value
CoolantTemperatureType	Flag	0 or Constant 1 or TerminalAverageValue	The flag for coolant temperature type Use constant. Refer to Terminal Average Value.
RotationSpeedType	Flag	0 or Constant 1 or PointArray 2 or DriveCycleReference	The flag for rotation speed type The constant type. The point array type. Reference Condition
RotationSpeed	Double		Rotation Speed
RotationSpeedVsTime	Table		The rotation speed vs time point array
SprayNozzleLocation	Flag	0 or None 1 or BothSides 2 or FrontSide 3 or RearSide	The flag for spray nozzle location No nozzle. Both side nozzle. Front side nozzle. Rear side nozzle.
CloseHollowShaftOutlet	Flag	0 or Off 1 or On	The flag for closing the hollow shaft outlet Open the hollow shaft outlet Close the hollow shaft outlet
FrontNozzleRatio	Double		The front nozzle ratio
RearNozzleRatio	Double		The rear nozzle ratio
ReferDriveCycleCondition	Int		Refer drive cycle condition

Bearing(Bearing)

The bearing

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
ShaftDiameter	Double		The shaft diameter
BearingDiameter	Double		The bearing diameter
BearingWidth	Double		The bearing width
BearingResistanceCalculationType	Flag	0 or Dimensions 1 or DimensionsAndGap	The type of bearing resistance calculation From dimensions. From dimensions and gap
BearingEquivalentGapType	Flag	0 or Custom 1 or Bearing1 2 or Bearing2	The type of bearing resistance calculation Use custom. Use Bearing1 (0.2mm). Use Bearing2 (0.4mm).
BearingEquivalentGap	Double		The bearing equivalent gap
BearingGapConductivity	Double		The bearing gap thermal conductivity
ShaftBearingFitType	Flag	0 or Custom 1 or GoodFit 2 or BadFit	The flag for shaft bearing fit type Use custom. Use good fit. Use bad fit.
ShaftBearingGap	Double		The shaft bearing gap
ShaftBearingThermalConductivity	Double		The shaft bearing thermal conductivity
BearingEndCapFitType	Flag	0 or Custom 1 or GoodFit 2 or BadFit	The flag for bearing end cap fit type Use custom. Use good fit. Use bad fit.
BearingEndCapGap	Double		The bearing end cap gap
BearingEndCapThermalConductivity	Double		The bearing end cap thermal conductivity
BearingResistanceCorrectionCoefficient	Double		The correction coefficient of bearing thermal resistance
ShaftBearingResistanceCorrectionCoefficient	Double		The correction coefficient of shaft bearing thermal resistance
BearingEndCapResistanceCorrectionCoefficient	Double		The correction coefficient of bearing end cap thermal resistance
ExponentBearingInner	Double		The exponent of the bearing inner race loss function
ReferenceHeatGenerationBearingInner	Double		The heat generation amount at reference speed for the bearing inner loss function
ReferenceSpeedBearingInner	Double		The reference speed for the bearing inner loss function
ExponentBearingOuter	Double		The exponent of the bearing outer race loss function
ReferenceHeatGenerationBearingOuter	Double		The heat generation amount at reference speed for the bearing outer loss function
ReferenceSpeedBearingOuter	Double		The reference speed for the bearing outer loss function
SpeedSpecifyType	Flag	0 or ConstantSpeed 1 or TimeDependentSpeedPointSequence 2 or ReferenceCondition	The flag for speed specify type Constant Speed. Time Dependent Speed Point Sequence Reference Drive Cycle Condition
Speed	Double		The speed of the bearing
SpeedVsTime	Table		The speed vs time point array
ReferDriveCycleCondition	Int		Refer drive cycle condition

Thermal Circuit Control(HeatControl)

The heat control

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
InitialTemperature	Double		The initial temperature
HeatAnalysisTimeWidth	Double		The thermal circuit time width

Heat Generation(HeatGeneration)

The heat generation

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
HeatGeneration	Double		The heat generation
GenerationType	Flag	0 or Constant 1 or PointArray 3 or ReferCondition 4 or SpeedDependent 5 or ReferComponent	The flag for heat generation type The constant type. The temperature dependent type. Refer to Heat Generation Component Condition. The speed dependent type. Refer to Heat Resistor Component.
TempVsHeatGeneration	Table		The heat generation vs temperature point array
HeatGenerationRotationSpecifyType	Flag	0 or BearingLossFunction 1 or PointArray	The flag for heat generation speed specify type The heat generation speed function type. The heat generation speed point array type.
FunctionExponent	Double		The function exponent
FunctionHeatGeneration	Double		The heat generation amount at a certain point
FunctionSpeed	Double		The speed at a certain point
HeatGenerationVsSpeed	Table		The heat generation vs speed point array
SpeedSpecifyType	Flag	0 or ConstantSpeed 1 or PointArraySpeed 2 or ReferenceCondition	The flag for speed specify type The constant speed type. The speed time point array type. Reference Drive Cycle Condition
Speed	Double		The speed
SpeedVsTime	Table		The speed vs time point array
reference	Int		Reference component
ReferDriveCycleCondition	Int		Refer drive cycle condition

Heat Transfer(HeatTransfer)

The heat transfer

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
HeatTransfer	Double		The heat transfer
ReferenceTemperature	Double		The reference temperature
HeatTransferCoefficientType	Flag	0 or Constant 1 or PointArray	The heat transfer coefficient type The constant type. The point array type.
TempVsHeatTransfer	Table		The temperature vs thermal conductance point array

Thermal Resistor(ThermalResistor)

The thermal resistor

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
ThermalResistor	Double		The thermal resistance
ResistanceType	Flag	0 or Constant 1 or PointArray 3 or ThermalResistance 4 or ThermalResistanceCylindrical 5 or CoolingWaterJacket 6 or CoolingSpray 7 or CoolingATF 8 or CoolingForcedConvection 9 or CoolingNaturalConvection 10 or CoilAndCoreContact 11 or GeneralContact 12 or Suppress 13 or User-Defined 14 or ThermalResistanceAdvection 15 or ShaftCooling 16 or CoolingChannel	The flag for thermal resistance type The constant type. The point array type. The thermal conduction type. The thermal conduction cylindrical type. The water jacket cooling type. The spray cooling type. The ATF cooling type. The forced convection cooling type. The natural convection cooling type. The coil and core contact type. The general contact type. Suppress type User-Defined type The thermal resistance advection type. The shaft cooling type The cooling channel type
TempVsThermalResistance	Table		The thermal resistor vs temperature point array
ThermalResistorLength	Double		The thermal resistor length
ThermalResistorArea	Double		The thermal resistor area
ThermalResistorCylinderHeight	Double		The thermal resistor cylinder height
ThermalResistorOuterRadius	Double		The thermal resistor cylinder outer radius
ThermalResistorInnerRadius	Double		The thermal resistor cylinder inner radius
ThermalConductivity	Double		The thermal conductivity
ThermalCorrection	Double		The thermal correction coefficient
CustomInsulationThickness	Double		The custom insulation thickness
CustomWireDiameter	Double		The custom wire diameter
CustomFillFactor	Double		The custom fill factor
CustomTension	Double		The custom tension
CustomConductorLength	Double		The custom conductor length
CustomPressure	Double		The custom pressure
ContactType	Flag	0 or RoundWire 1 or RectangularWire	The flag for contact type The round wire type. The rectangular wire type.
ImpregnationType	Flag	0 or Off 1 or On	The flag for impregnation type No impregnation. Use impregnation.
FitType	Flag	0 or Custom 1 or GoodFit 2 or BadFit	The flag for fit type Use custom. Use good fit. Use bad fit.
CustomFit	Double		The custom fit length
CoolantType	Flag	1 or Water 2 or Oil 4 or Custom	The flag for coolant type Use water. Use oil. Use custom.
ForcedConvectionCoolantType	Flag	0 or Air 1 or Water 2 or Oil 4 or Custom	The flag for coolant type Use air. Use water. Use oil. Use custom.
NaturalConvectionCoolantType	Flag	0 or Air 1 or Water 2 or Oil 3 or ATFOil 4 or Custom	The flag for coolant type Use air. Use water. Use oil. Use ATF oil. Use custom.
AdvectionCoolantType	Flag	1 or Water 2 or Oil 3 or ATFOil 4 or Custom	The flag for advection coolant type Use water. Use oil. Use ATF oil. Use custom.
ATFCoolantType	Flag	3 or ATFOil 4 or Custom	The flag for ATF coolant type Use ATF oil. Use custom.
ChannelConvectionCoolantType	Flag	0 or Air 1 or Water 2 or Oil 3 or ATFOil 4 or Custom	The flag for coolant type Use air. Use water. Use oil. Use ATF oil. Use custom.
Characteristic Length	Double		The characteristic length
InputFlowType	Flag	0 or FlowVelocity 1 or VolumeFlowRate 2 or ReferenceFlowCircuit	The flag for input flow type Use flow velocity. Use volume flow rate. Reference flow circuit.
FlowVelocity	Double		The flow velocity
VolumeFlowRate	Double		The volume flow rate
NozzleDiameter	Double		The nozzle diameter
CoolingJacketType	Flag	0 or Spiral 1 or Axial 2 or None	The flag for cooling jacket type Use spiral. Use axial. None.
CoolingJacketTubeWidth	Double		The rectangular tube width
CoolingJacketTubeHeight	Double		The rectangular tube height
NumCoolingJacketTubes	Double		The number of rectangular tubes
CoolingJacketRadius	Double		The cooling jacket radius
RectangularTubeLength	Double		The cooling jacket tube length
CoolingJacketArea	Double		The cooling jacket area
ForcedConvectionType	Flag	0 or Circumferential 1 or AxisDirection 2 or MotorGap 3 or MotorGapAxial	The flag for forced convection type Use circumferential. Use axis direction. Use motor gap (radial). Use motor gap (axial).
GapWidth	Double		The gap width
RotorRadius	Double		The rotor radius
NaturalConvectionType	Flag	0 or HorizontalCylinder 1 or VerticalCylinder 2 or VerticalFlatPlate 3 or HorizontalPlateUpper 4 or HorizontalPlateLower	The flag for natural convection type Use horizontal cylinder. Use vertical cylinder. Use vertical flat plate. Use horizontal plate upper. Use horizontal plate lower.
CoolingMaterialTable	Table		The cooling material table
CoolantTemperatureType	Flag	0 or Constant 1 or TerminalAverageValue	The flag for coolant temperature type Use constant. Refer to Terminal Average Value.
CoolantTemperatureConstantValue	Double		The coolant temperature constant value
PreviewCoolantTemperature	Double		The coolant temperature (preview)
PreviewTerminalTemperature1	Double		The terminal temperature 1 (preview)
PreviewTerminalTemperature2	Double		The terminal temperature 2 (preview)
ThermalUserDefinedScript	String		The python script for thermal resistance
ShaftLength	Double		The shaft length
ShaftCoolantType	Flag	1 or Water 2 or Oil 3 or ATFOil 4 or Custom	The flag for shaft coolant type Use water. Use oil. Use ATF oil. Use custom.
RotationSpeedType	Flag	0 or Constant 1 or PointArray 2 or DriveCycleReference	The flag for rotation speed type The constant type. The point array type. Reference Condition
RotationSpeed	Double		Rotation Speed
RotationSpeedVsTime	Table		The rotation speed vs time point array
GapFlowType	Flag	0 or GapFlowVelocity 1 or GapRotationSpeed	The flag for gap flow type Use flow velocity. Use rotation speed.
SprayType	Flag	0 or GeneralSpray 1 or SpecifyNozzlePosition	The flag for spray type Use general spray. Specify nozzle position.
NozzlePosition	Flag	0 or SprayHousing 1 or SprayEndCap 2 or SprayShaft	The flag for nozzle position Spray from housing. Spray from end cap. Spray from shaft.
SprayAngle	Double		The spray angle
ShaftInnerRadius	Double		The shaft inner radius
ShaftOuterRadius	Double		The shaft outer radius
CoilInnerRadius	Double		The coil inner radius
CoilOuterRadius	Double		The coil outer radius
HousingInnerRadius	Double		The housing inner radius
CoilEndHeight	Double		The coil end height
EndCapDistance	Double		The end cap distance
AreaCorrectionType	Flag	0 or AreaCorrectionFactor 1 or CoilEndArea	The flag for area correction type Use area correction factor. Use coil end surface area.
AreaCorrectionFactor	Double		The area correction factor
CoilEndArea	Double		The coil end area
ChannelType	Flag	0 or CircleChannel 1 or RectangleChannel	The channel type Circle type. Rectangle type.
CircularDiameter	Double		The circular diameter
NumberChannel	Double		The number of channel
ChannelLength	Double		The channel length
RotationFlag	Flag	0 or NoConsideringRotation 1 or ConsideringRotation	The flag of considering rotation Do not considering rotation. Considering rotation.
CircumferentiallyDistributedFlag	Flag	0 or NoCircumferentiallyDistributed 1 or CircumferentiallyDistributed	The flag of circumferentially distributed Do not circumferentially distributed. Circumferentially distributed.
RotationDiameter	Double		The rotation diameter
HasFins	Flag	0 or Off 1 or On	The flag for fins The surface does not have fins. The surface has fins.
FinInterval	Double		The fin interval
FinLength	Double		The fin length
FinHeight	Double		The fin height
FinNumber	Flag		The fin number
ReferThermalProbe	Flag	0 or Off 1 or On	Reference thermal probe Not refer to thermal probe. Refer to thermal probe.
ReferenceThermalProbe	Int		The referenced thermal probe id
ReferenceFlowRateProbe	Int		The referenced flow rate probe id
PreviewVolumeFlowRate	Double		The volume flow rate (preview)
PreviewFlowVelocity	Double		The flow velocity (preview)
UseAxialFlow	Flag	0 or Off 1 or On	The flag for use axial flow Considering axial flow. Does not consider axial flow.
AxialInputFlowType	Flag	0 or FlowVelocity 1 or VolumeFlowRate 2 or ReferenceFlowCircuit	The flag for axial input flow type Use flow velocity. Use volume flow rate. Reference flow circuit.
AxialFlowVelocity	Double		The axial flow velocity
AxialVolumeFlowRate	Double		The axial volume flow rate
AxialLength	Double		The axial length
AxialReferenceFlowRateProbe	Int		The axial referenced flow rate probe id
ReferDriveCycleCondition	Int		Refer drive cycle condition

Cooling Jacket(CoolingJacket)

The cooling jacket

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
InputFlowType	Flag	0 or FlowVelocity 1 or VolumeFlowRate 2 or ReferenceFlowCircuit	The flag for input flow type Use flow velocity. Use volume flow rate. Reference flow circuit.
FlowVelocity	Double		The flow velocity
VolumeFlowRate	Double		The volume flow rate
CoolingJacketType	Flag	0 or Spiral 1 or Axial 2 or None	The flag for cooling jacket type Use spiral. Use axial. None.
CoolingJacketTubeWidth	Double		The rectangular tube width
CoolingJacketTubeHeight	Double		The rectangular tube height
NumCoolingJacketTubes	Double		The number of rectangular tubes
CoolingJacketRadius	Double		The cooling jacket radius
RectangularTubeLength	Double		The cooling jacket tube length
CoolingJacketArea	Double		The cooling jacket area
ThermalCorrection	Double		The thermal correction coefficient
ReferenceFlowRateProbe	Int		The referenced flow rate probe id
PreviewVolumeFlowRate	Double		The volume flow rate (preview)
PreviewFlowVelocity	Double		The flow velocity (preview)
AdvectionThermalCorrection	Double		The advection thermal correction coefficient
CoolantType	Flag	1 or Water 2 or Oil 4 or Custom	The flag for coolant type Use water. Use oil. Use custom.
CoolingMaterialTable	Table		The cooling material table
CoolantTemperatureType	Flag	0 or Constant 1 or TerminalAverageValue	The flag for coolant temperature type Use constant. Refer to Terminal Average Value.
CoolantTemperatureConstantValue	Double		The coolant temperature constant value
ResolutionOfTemperatureDistribution	Flag		The resolution of temperature distribution

Heat Capacity(HeatCapacity)

The heat capacity

Property (propName)	Type (Type)	Flag (scriptKeyName)	Description
HeatCapacity	Double		The heat capacity
CapacityType	Flag	0 or Constant 1 or PointArray 3 or HeatCapacity	The flag for heat capacity type The constant type. The point array type. The heat capacity type.
TempVsHeatCapacity	Table		The heat capacity vs temperature point array
ThermalCapacitanceDensity	Double		The thermal capacitance density
ThermalCapacitanceSpecificHeat	Double		The thermal capacitance specific heat
ThermalCapacitanceVolume	Double		The thermal capacitance volume
ThermalCorrection	Double		The thermal correction coefficient