Function Tutorials

[JFT145] How to Arrange Windings That Are in Parallel Circuits on Specified Layers

This document explains the procedure on how to set series-parallels of coils and switch the position in slots.

[JFT133] System Loss Evaluations in System-Level Simulations

This document describes the method to output an efficiency map / loss map obtained with JMAG and using a circuit simulation to comprehend drive cycle system loss.

• Technical Themes: Efficiency Map

[JFT127] Changing Settings for Parallel Computing When Executing Calculations

This document describes the procedure for changing settings for parallel computing when executing calculations.

[JFT128] Evaluating Drive Cycle Time Using Efficiency Maps

DATAFile nameSize (KB)GuideJFT128DriveMode-e.pdf443Sample DataJMAG-Designer 20.1JFT128DriveMode.zip2,877Case

[JFT131] Evaluating Degrees of Similarity for Geometry Using NGnet Weight

This document describes a method where after executing topology optimization using NGnet, degrees of similarity for geometry from NGnet weight are evaluated.

• Technical Themes: Design Exploration / Optimization

[JFT125] Inheriting Operating Points Between Modes in Efficiency Map Studies

This document describes the method for using operating point information obtained with speed priority mode in accuracy priority mode.

• Technical Themes: Design Exploration / Optimization, Efficiency Map, and MBD

[JFT136] Sending SSH Settings to Remote Machines

This document describes the method for sending SSH settings configured on local machines to remote machines for executing other case calculations.

• Technical Themes: Design Exploration / Optimization

[JFT128] Evaluating Drive Cycle Time Using Efficiency Maps

This document describes the method for using obtained efficiency maps to confirm the efficiency history, operating points, cluster points, and total energy, etc., for drive cycle …

• Technical Themes: Efficiency Map

[JFT125] Inheriting Operating Points Between Modes in Efficiency Map Studies

DATAFile nameSize (KB)GuideJFT125EfficiencyMapOperatingPoint-e.pdf367Sample DataJMAG-Designer 20.1JFT125EfficiencyMapOperatingPoint.zip2,828Case

[JFT126] Vectorizing Signals in a Control Circuit (MUX, DEMUX)

DATAFile nameSize (KB)GuideJFT126MUX-e.pdf271Sample DataJMAG-Designer 20.1JFT126MUX.zip70Case

[JFT131] Evaluating Degrees of Similarity for Geometry Using NGnet Weight

DATAFile nameSize (KB)GuideJFT131TopologyOptNGnet-e.pdf400Sample DataJMAG-Designer 20.1JFT131TopologyOptNGnet.zip138Case

[JFT127] Changing Settings for Parallel Computing When Executing Calculations

DATAFile nameSize (KB)GuideJFT127ParallelCalcSettings-e.pdf289Sample DataJMAG-Designer 20.1JFT127ParallelCalcSettings.zip449Case

[JFT126] Vectorizing Signals in a Control Circuit (MUX, DEMUX)

This document describes the methods for using a signal vectorization component (MUX) and vector disassembling component (DEMUX) in a control circuit.

[JFT136] Sending SSH Settings to Remote Machines

DATAFile nameSize (KB)GuideJFT136SendSSHToRemoteMachine-e.pdf449Sample DataJMAG-Designer 20.1JFT136SendSSHToRemoteMachine.zip285Case

[JFT133] System Loss Evaluations in System-Level Simulations

DATAFile nameSize (KB)GuideJFT133SystemSimUsingRTEmap-e.pdf529Sample DataJMAG-Designer 20.1JFT133SystemSimUsingRTEmap.zip7,679Case

[JFT123] Accounting for Residual Strain

This document explains the procedure for executing magnetic field analysis and iron loss analysis that account for residual strain.

• Technical Themes: Material Modeling / Loss Analysis