[JFT093] Shape Modification Using the Morphing Function (Moving Only Nodes on a Specified Edge)

In this document, the procedure for moving only nodes in a mesh model on specified edges using the morphing function is presented.

[JFT100] Material Allotment per Element

DATAFile nameSize (KB)GuideJFT100ChangeMaterialPerElement-e.pdf345Sample DataJMAG-Designer 19.0JFT100ChangeMaterialPerElement.zip78Case

[JFT100] Material Allotment per Element

In this document, how to set a different material for each element of a part and how to create multiple cases with different material specifications for the elements is presented.

• Technical Themes: Design Exploration / Optimization

[JFT104] Application of an Anomalous Eddy Current Loss Factor Dependent on Magnetic Flux Density and Frequency

In this document, an anomalous eddy current loss factor table is created in which an anomalous eddy current loss correction factor is dependent on frequency and magnetic flux dens…

• Technical Themes: Material Modeling / Loss Analysis

[JFT096] Performing Parametric Analysis Using an Analysis Parameter View

DATAFile nameSize (KB)GuideJFT096ParametricAnalysis_ParameterView-e.pdf230Sample DataJMAG-Designer 19.0JFT096ParametricAnalysis_ParameterView.zip334Case

[JFT104] Application of an Anomalous Eddy Current Loss Factor Dependent on Magnetic Flux Density and Frequency

DownloadVersionSize (KB)Guide (PDF) -459Sample Data JMAG-Designer 19.0130Case

[JFT098] Automatic Thread Allocation During Local Job Execution

DATAFile nameSize (KB)GuideJFT098Affinity-e.pdf339Sample DataJMAG-Designer 19.0JFT098Affinity.zip413Case

[JFT098] Automatic Thread Allocation During Local Job Execution

In this document, how to optimally allocate threads to cores is presented.

• Technical Themes: Design Exploration / Optimization

[JFT096] Performing Parametric Analysis Using an Analysis Parameter View

In this document, how to perform parametric analysis using an analysis parameter view and how to check the results is presented.

• Technical Themes: Design Exploration / Optimization

[JFT088] Iron Loss Analysis Using Iron Loss Characteristics Data (Isolation of Excess Eddy Current Loss)

DATAFile nameSize (KB)GuideJFT088IronLossCalculation_B-e.pdf342Sample DataJMAG-Designer 18.0JFT088IronLossCalculation_B.zip 124Case

[JFT084] Procedure for Two-Way Coupled Analysis Taking into Account Fluid Force with JMAG and STAR-CCM+

In this document, how to set up a two-way coupled analysis that takes into account fluid force with JMAG and STAR-CCM+ is presented.

• Technical Themes: MBD and Multiphysics

[JFT084] Procedure for Two-Way Coupled Analysis Taking into Account Fluid Force with JMAG and STAR-CCM+

DATAFile nameSize (KB)GuideJFT084JMAG_STARCCM+-Motion-e.pdf428Sample DataJMAG-Designer 18.1JFT084JMAG_STARCCM+-Motion.zip29,031Case

[JFT068] Specifying Three-Phase Synchronous Motor dq Axis Current

DATAFile nameSize (KB)GuideJFT068IdIqCommand-e.pdf343Sample DataJMAG-Designer 18.1JFT068IdIqCommand.zip239Case

[JFT081] Creating an Induction Motor Efficiency Map Using JMAG-Designer (Speed Priority Mode)

In this document, how to create an efficiency map of an induction motor using an efficiency map study (speed priority mode) in JMAG-Designer is presented.

• Technical Themes: Design Exploration / Optimization, Efficiency map, and MBD

[JFT081] Creating an Induction Motor Efficiency Map Using JMAG-Designer (Speed Priority Mode)

DATAFile nameSize (KB)GuideJFT081EfficiencyMapStudySpeed-IM-e.pdf232Sample DataJMAG-Designer 18.1JFT081EfficiencyMapStudySpeed-IM.zip1,169Case

[JFT057] How to Run Topology Optimization

DATAFile nameSize (KB)GuideJFT057TopologyOptimization-e.pdf276Sample DataJMAG-Designer 18.1JFT057TopologyOptimization.zip196Case