DP
Transient Magnetic (2D/Axisymmetric)
- Sort condition
- Newest first
- Oldest first
- Views
-
262 – IPM Motor Thermal Demagnetization Analysis with Incomplete Magnetization of Dy Diffusion Magnets
In this example, a motor using Dy diffused magnets the thermal demagnetization resistance of the Dy diffused magnets with a coercive force distribution when there is incomplete ma…
-
223 – Multi-Objective Optimization of an IPM Motor Account Stress at High-Speed Rotation
In this example, the optimum current phase that achieves high torque per each geometry is obtained, and the torque characteristics (1,000 r/min) and stress due to centrifugal forc…
-
252 – Geometry Optimization of a Solenoid Valve
In this example, an example where the geometry of a solenoid valve is optimized using a multi-objective optimization algorithm is presented.
-
259 – Automatically Searching for Current Phase that Obtains Maximum Torque and Evaluating Torque Characteristics
In this example, a search is performed for the current phase that maximizes torque for each of 3 rotor geometries. Motor average currents and torque ripples are evaluated using th…
-
261 – SPM Motor Magnet Coercive Force Optimization For Obtaining Sinusoidal Magnetization
In this example, a magnet is segmented into blocks and coercive force is defined. The coercive force of each block is calculated so that the induced voltage waveform approaches a …
-
200 – Iron Loss Analysis of IPM Motor using Hysteresis Model
In this example, a hysteresis model accounting for minor loops of the direct current bias magnetism and the lamination analysis function accounting for eddy current distribution i…
-
20 – Sound Pressure Analysis of an SPM Motor
This Application Note shows an example of an evaluation of a reactor’s sound pressure, when acquiring electromagnetic force generated by a stator core for a SPM motor and linking …
-
215 – Simulation of an IPM Motor with a Delta Connection Using a Control Simulator and JMAG-RT
In this example, a JMAG-RT model is incorporated into a control/circuit simulator to monitor the circulating current when an IPM motor is being driven.
-
240 – NT Characteristics Analysis of an IPM Motor Using PAM Drive
In this example, an example of evaluating the performance of an IPM with PAM operation is presented.
-
244 – Magnetic Field Strength Analysis at a Sensor Position
In this example, with the analysis target being a motor and the detection sensor being a TMR sensor, an example where a detection signal waveform is obtained that is based on magn…
-
226 – Vibration Characteristics Analysis of SPM Motors
In this example, the acceleration is evaluated by obtaining the electromagnetic force generated in the stator core of the SPM motor at multiple rotation speeds and coupling with t…
-
192 – Response Characteristics Analysis of Solenoid Valves Accounting for Residual Magnetization
Here, we will discuss the steps to investigate the effect on responsiveness caused by residual magnetization generated in the magnetic materials, and look at case examples.
-
222 – Irreversible Thermal Demagnetization Analysis of Incompletely Magnetized Magnets
In this example, analysis is performed while varying the temperature of magnetized magnets, and then the influence on the torque waveform and magnetic flux density distribution is…
-
214 – Monitoring the Radial Force Acting on the Teeth of IPM Motors Using Circuit Control Simulation
In this example, an IPM motor as a JMAG-RT model is captured in a control/circuit simulator, and radial forces acting on the teeth during motor driving is monitored while changing…
-
241 – Single-Phase Synchronous Motor N-T-I Characteristics Analysis
In this example, a use case in which the N-T-I characteristics for a single-phase synchronous motor are obtained is presented.
-
225 – Induced Voltage Analysis of Memory Motor using Variable Magnetized Magnet
In this example, the change in motor characteristics are checked as the memory motor variable magnet magnetization is changed using the three-phase coil current. One example of mo…
