DP
Transient Magnetic (2D/Axisymmetric)
- Sort condition
- Newest first
- Oldest first
- Large number of views
-
[JAC213] Circuit/Control Simulation of a Wound-Field Synchronous Motor
In this example, JMAG-RT is used to obtain the torque of a wound-field synchronous motor (below WFSM) and the coil inductance current dependence, and the spatial harmonic componen…
-
[JAC268] SPM Motor Teeth Geometry Topology Optimization
In this example, the on / off method is used to search for stator teeth geometry that maximizes average torque and minimizes torque ripple with the entire areas of stator teeth ti…
-
[JAC192] Response Characteristics Analysis of Solenoid Valves Accounting for Residual Magnetization
In this example. we will discuss the steps to investigate the effect on responsiveness caused by residual magnetization generated in the magnetic materials, and look at case examp…
-
[JAC115] Eccentricity Analysis of an SPM Motor
This Application Note presents how to evaluate the cogging torque waveform and effects on the electromagnetic force acting on the stator in an SPM motor with and without eccentric…
-
[JAC240] NT Characteristics Analysis of an IPM Motor Using PAM Drive
In this example, an example of evaluating the performance of an IPM with PAM operation is presented.
-
[JAC234] Vibration Characteristics Analysis of an Induction Motor
In this example, electromagnetic force generated in the induction motor stator core is obtained, and an example of evaluating sound pressure by linking it with the eigenmode of th…
-
[JFT142] Creating Shapes Using a Local Coordinate System
This document describes the method for using local coordinate systems to create shapes and changing the shapes parametrically.
-
[JFT135] Distributed Execution of Topology Optimization Calculation Using SSH
This document describes how to perform topology optimization calculations with the on/off method on a Linux remote machine via SSH.
-
[JFT147] Creating a Lookup Table Using Parametric Analysis
This document explains how to run parametric analysis in JMAG-Designer and register it as a lookup table for MATLAB.
-
[JFT137] Current Restraints using Conditional Branches of Equation
This document explains how to restrain current value that is fed into the coils when geometry and electric resistance change.
-
[JFT144] Flux Linkage Calculations in a Specified Position
This document explains the procedure to set user-selected points in air regions and calculate flux linkage at these points.
-
[JFT141] JMAG-RT Model Data File Creation Function in JMAG-Designer
This document will show you how to export the efficiency map/loss map obtained in JMAG as a JMAG-RT model data file and to check the plot in JMAG RT-Viewer.
-
[JFT145] How to Arrange Windings That Are in Parallel Circuits on Specified Layers
This document explains the procedure on how to set series-parallels of coils and switch the position in slots.
-
[RTML-050] PMSM/IPM 3-Phases Delta
Type: PMSM | Power: 150(W) | Stator(Outside Diameter): 112(mm) | Height: 65(mm) | Voltage/Current: DC24(V)/4(A) | Rotor/Mover: IPM
-
[RTML-049] PMSM/IPM Constant rating 75(kW) 3-phase Resolver
Type: PMSM | Power: 75(kW) | Stator(Outside Diameter): 212(mm) | Height: 200(mm) | Voltage/Current: DC600(V)/250(A) | Rotor/Mover: IPM
-
[RTML-048] WFSM_02
Type: WFSM | Max Power: 2(kW) | Stator(Outside Diameter): 260(mm) | Height: 60(mm) | Voltage/Current: DC200(V)/20(A),DC100(V)/10(A) | Rotor/Mover: WF | Number of Phases: 6
