Documents that we were particularly going to introduce to everyone at the exhibition are now available to view online.
[JAC225] Induced Voltage Analysis on Memory Motors Using Variable Magnets
[JAC262] IPM Motor Thermal Demagnetization Analysis Accounting for Dy-Diffusion Magnet Incomplete Magnetization
[JFT102] Setting 3D Model Coils Using the Winding Editor
[L-MO-77] Motor Concept Design with JMAG-Express and JMAG-RT Viewer
Prof. Miller
Webinar: Brush up on Motor Design!
Webinar: Brush up on Motor Design!
[JAC205] Analyzing the Torque Characteristics of IPM Motors Using a Thermal Equivalent Circuit
[W-SE-72] Reduction of Time Steps by Using Time Periodic Explicit Error Correction Method
[JAC226] Vibration Characteristics Analysis of SPM Motors
[JFT054] Electromagnetic Force Spatial Modes Acting on a Stator
[W-MO-23] Measurement of PM Motor Vibration/Noise and Analysis Modeling
[L-MU-93] JMAG/Adams/Simulink Coupled Vehicle Drive Simulation
[JAC223] Multi-Objective Optimization of an IPM Motor Accounting for Stress at High-Speed Rotation
[JAC217] Creating Efficiency Maps for 3-Phase Induction Motors
[JAC237] AC Loss Analysis of an IPM Moto
[JFT070] Creating a PM motor Efficiency Map Using JMAG-Designer (Accuracy Priority Mode)
[W-MB-102] Motor Efficiency Map Evaluation for Model-Based Development (MBD) Using FEA Simulation
[W-SE-101] Detailed Eddy Current Analysis of End Winding with Parallel Processing
[JAC223] Multi-Objective Optimization of an IPM Motor Accounting for Stress at High-Speed Rotation
[JFT103] Performing Topology Optimization Using Sensitivity Analysis
[W-OP-96] Necessity of GA for Multi-Objective Optimization of Drive Motor
[L-OP-109] Exploration of New Ideas Using Topology Optimization
[JAC205] Analyzing the Torque Characteristics of IPM Motors Using a Thermal Equivalent Circuit
[JAC228] Induction Motor Thermal Analysis
[JFT015] Procedure for Two Way Coupled Analysis with JMAG and STAR-CCM+ Taking Thermal Fluid into Account
[L-MU-92] JMAG/Particleworks Coupled Motor Cooling Analysis
[JAC262] IPM Motor Thermal Demagnetization Analysis Accounting for Dy-Diffusion Magnet Incomplete Magnetization
[JAC230] 6-Phase SPM Motor Inverter Fault Simulation
[JFT077] Creating JMAG-RT Models with Generic Circuit Topology
[L-MB-55] High Fidelity Behavior Models Generation for Control/Circuit Simulation using JMAG-RT
[W-MB-65] The Necessity of JMAG-RT 3D Models
[W-MB-102] Motor Efficiency Map Evaluation for Model-Based Development (MBD) Using FEA Simulation
[JAC218] High-Frequency Induction Hardening Analysis Accounting for Deformation
[JAC220] Analysis of the High-Frequency Induction Hardening and Cooling of a Gear
[JAC233] Induction Heating Coil Optimization
[W-SE-145] Highly Parallel Solver Performance Evaluation (Induction Heating)
[JAC098] Response Analysis of a Solenoid Valve Using a Control Simulator and the JMAG-RT
[JAC192] Response Characteristics Analysis of Solenoid Valves Accounting for Residual Magnetization
[JAC252] Geometry Optimization of a Solenoid Valve
[L-MB-79] Accounting for Circuit Coupling Functions with Control Systems
[JAC004] Sound Pressure Analysis of a Reactor
[JAC196] Analysis of coil stray capacitance
[JAC224] Wireless Power Transfer Device Stray Loss Analysis
[JAC238] Hysteresis Loss Analysis in a Reactor with DC Bias
[W-SE-72] Reduction of Time Steps by Using Time Periodic Explicit Error Correction Method
[W-HU-71] Notes on Performance Evaluation and Hardware Selection of JMAG Parallel Solver
[W-SE-74] Electromagnetic Force Calculations Using the Adaptive Function
[W-SE-101] Detailed Eddy Current Analysis of End Winding with Parallel Processing
[L-SE-116] Accuracy Improvement of Electromagnetic Force Calculation Using Correction
[W-SE-72] Reduction of Time Steps by Using Time Periodic Explicit Error Correction Method